疾速卷帘门的电机的一样平常维护要点! - 公司动向-lehu88乐虎游戏官网门业有限公司

lehu88乐虎游戏官网-乐虎lehu66_送彩金app

征询热线
-->
以后地位: 首页 > 讯息中央 > 公司动向 >

疾速卷帘门的电机的一样平常维护要点!

公布人:    公布日期:2020-11-06 16:14:20

疾速卷帘门是疾速起落的无妨碍断绝门,次要功用是保温、保湿、防尘、防虫、隔音等,使车间坚持恒温、恒湿、干净的任务情况。实用于食品、医药、电子、橡胶、化工、汽车、纺织、物流等范畴。
The fast rolling shutter door is a barrier free isolation door with rapid lifting. Its main functions are heat preservation, moisture preservation, dust prevention, insect prevention and sound insulation, so as to maintain a constant temperature, constant humidity and clean working environment in the workshop. It is suitable for food, medicine, electronics, rubber, chemical industry, automobile, textile, logistics and other fields.
疾速卷帘门的运作次要便是靠电机,以是一样平常维护对电机的运用很紧张!上面就来为您简述一下疾速卷帘门电机的几个维护要点:
The operation of the fast rolling shutter door mainly depends on the motor, so the daily maintenance of the motor is very important! The following will briefly describe the maintenance points of the motor of fast rolling shutter door:
1、疾速卷帘门的电机运用时应在枯燥情况中停止,电机外表应坚持干净,进风口不克不及有尘土、纤维等。
1. The motor of the fast rolling shutter door should be used in a dry environment. The surface of the motor should be kept clean and there should be no dust and fiber in the air inlet.
2、当电动机的热维护连续发作办法时,应查明缺点来自电动机还是超负荷或维护装置整定值太低,消除缺点后,方可投入运转。
2. When the thermal maintenance of the electric motor continues to take action, it should be found out that the problem comes from the overload of the electric motor or the setting value of the maintenance and installation is too low. After the problem is eliminated, it can be put into operation.
3、应该包管电动机在运转历程中的润滑无妨碍。平凡的电动机运转5000小时左右,即应补充或更换润滑脂,运转中发明轴承过热或润滑蜕变时,液压及时换润滑脂。
3. The smooth and unobstructed operation of the motor should be ensured. When the ordinary electric motor runs for about 5000 hours, the grease should be added or replaced. When the bearing is overheated or smooth degeneration is found in operation, the grease is changed by hydraulic pressure in real time.
4、当轴承的寿命停止时,电动机运转的噪声将分明增大,反省轴承的径向游隙抵达下列值时,即应更换轴承。
4. When the service life of the bearing is over, the noise of the motor will increase obviously. When the radial clearance of the bearing reaches the following value, the bearing should be replaced.
5、拆开电动机时,从轴伸端或非伸端取出转子都可以。假设没有需求卸下风扇,还是从非轴伸端取出转子较为便利,从定子中抽出转子时,应防止破坏定子绕组或绝缘。
5. When the motor is disassembled, the rotor can be pulled out from the extended or non extended end of the shaft. If there is no need to remove the fan, it is more convenient to take out the rotor from the non shaft extension end. When pulling out the rotor from the stator, the stator winding or insulation should be avoided.
6、更换绕组时必须记下原绕组的方法,尺寸及匝数,线规等,当丧失了这些数据时,应向制造厂讨取,随意变动原设计绕组,常常使电动机某项或几项功用好转,乃至于无法运用。
6. When changing the winding, it is necessary to record the mode, size, turns, wire gauge, etc. of the original winding. When these data are lost, they should be obtained from the manufacturer, and the original designed winding can be changed at will. As a result, some or several functions of the electric motor will be deteriorated or even can not be used.
上一篇:别墅lehu88乐虎游戏官网中的平轮有什么作用?
下一篇:哪种材质的lehu88乐虎游戏官网更具防盗功能
产物中央
联络我们